2021-02-02-00
1: Add parameter No. 269 [Debug printing enable]; debugging information will not be prompted in the disabled mode;

2021-04-08-00
1: When modifying the continuous spiral arc command, the cumulative error problem occurs;


2021-04-29-00
1: Add a special interface for testing, long press the [Cancel] key to enter the main interface;


2021-05-17-00
1: Increase the virtual key character, the character content can be expanded;

2021-08-11-00
1:Increase the Russian font, the Russian translation package is not translated

2021-08-12-00
1: Solve the problem that the five-axis coordinate is not displayed in the teaching interface of [Program], and the 3 and 4 axes are displayed normally.
2: Add Russian translation package (Special thanks: ֧ԧ֧ ѧӧڧߧܧڧ)

2021-09-03-00
1: Open M3K accessory panel function, 268 set accessory panel model

2021-09-09-00
1: File display remove path name

2021-11-19-00
1Increase system self-test interface

2021-11-22-00
1Modify the record box control bug

2021-12-07-02
1: Increase the parameters of 271, the maximum contour error; the default is 0; the value setting, the faster the speed, the more smooth. It is recommended to set up 0.002mm;

2021-12-10-00
1: Teach the increasing entry of the fourth axis of the fourth shaft;

2021-12-14-00
1: Add new hardware support


2022-01-07-00
1: Modify the boot file copy protection

2022-01-10-00
1: Registration number limit

2022-01-17-01
1: Compatible with new hardware

2022-01-25-00
1: Increase the test file


2022-01-26-00
1: Adjust the test interface


2022-02-08-00
1: Increase the free configuration of the physical axis (the main from the axis);
    488-492: The program axis corresponding to the physical axis can be configured,
    The programming axis of the default physical axis is: x y z 4th 5th
E.g:
   If you want to configure the fourth axis into the slave axis of the double Y axis Y, you can set the 491 parameter to y.

2022-03-02-00
1: Add system folder erroneous deletion; note: NAND1-1 folder is forbidden to delete, otherwise the system crashes!

2022-03-17-00
1: Compatible 2020-401-02 Hardware firmware version

2022-03-23-01
1:Teach (Guided Programming) function.The key function index number is: 1398

2022-03-24-00
1: Increase the label machine print macro address # 1619;

2022-04-03-01
1: Modify the test interface label print;

2022-04-08-00
1: Add 272-277 parameters, external input buttons can be customized;

2022-04-11-01
1: # 988- # 992 Physical axis and program axis configuration macro address.


2022-04-15-00
1: Increase user custom CAM, buttate the key index 1399.

2022-04-18-01
1: Increase the function shortcut key in the division, and the keys to the key section is: 1334.

2022-05-13-01
1: Parameter interface increases#50-#499 saving and loading function, file path: Local/uservar


2022-05-23-01
1: Modify the test interface [Hardware error] Mistake display problem;
2: Add record to the file macro function: RECORD[];

2022-05-23-02
1:RECORD[x1,x2,x3,x4,x5,x6,x7]  Maximum save 5 data;

2022-05-24-01
1: Record [] can customize the preservation content format;

2022-05-25-00
Optimize record [] saving method

2022-06-02-00
1:Add 279 parameter MODBUS RTU
2:Add Modbus RTU to write macro function MSETDATA [];

2022-06-09-00
1: Add Modbus RTU Reading Macros: Mgetdata [];
2: Add Modbus RTU data conversion macro function: mdata2byte [];
3: Add Modbus RTU data conversion macro function: MBYTE2DATA [];

2022-06-15-00
1: Support M3K and Modbus RTUs at the same time.

2022-06-29-00
1: Improve the definition of the USB standard keyboard and add 15 custom function keys.


2022-07-01-00
1: Improve the MODBUS macro function

2022-07-05-00
1: Modify the manual mobile axis affects the problem of stopping the main axis of the servo.

2022-09-26-00
1:#1505 modal dialog box increases the return value, 0: cancel key 1: OK key.

2023-01-04-01
1: Compatible with new hardware.
2: Add G100-G199 parameter macro address;

2023-05-05-00
1SQRT [] increase the validity of the value

2023-05-08-00
1: Increase the macro function   ROUND[ ];

2023-05-15-00
1: System boot only loads the slib-g.NC slib-m.NC slibuser.nc three library files;

2023-05-24-00
1: Key index 1389 can enter the local disk on any interface;
2: Add shortcut code to the file interface: 1531: Copy 1532: Paste 1533: Copy to the U disk or local

2023-05-29-00
1: The files set up by the factory settings are: default_Setting

2023-06-06-00
1: The value protection of#578 and#1994 has been added;
2: No. 76 parameters can take effect without restarting;

2023-06-21-00
1: Fix: When the parameter file is not on the U disk, the error prompts to upgrade the parameter success;
2: M4 spindle start -stop light is turned on;
3: Amend the file interface F4 button title in real -time display;
4: Modify the file English,#842 title;
5: MDI increases ESC prompts;

2023-06-25-01
1: Repair: Run the M30 crash (06-06 starts to appear);
2: Repair: The files without a change of lines at the end will delete the character's problem when editing;


2023-09-17-00
1: Resolve the issue of garbled display caused by excessively long comment text!


2023-10-31-00
1: Solve the problem of invalid local disk clearing function in V2 version; 

2023-11-09-00
1: Added parameter number 253, does the feed rate adjustment apply to G0?

2023-12-18-01
1: Added parameter number 295, feed rate maximum value;
2:Place the actual maximum error of the zero switch in the macro variable #2106.

2023-12-19-00
1: Increase the key value and status macro address, #2038, which is readable and writable. It needs to be cleared before use.


2024-01-05-00
1: Resolved the issue of rebooting in multi-level folders for V1 version.
2: Added super administrator privileges to one-click backup.
3:Fixing character encoding issues in the [eng] file.
4:Update the latest Russian translation files: msg2 and rus. Thanks, ڧܧݧѧ ӧԧڧߧ֧.
5: Open optimization parameters for speeds 280 and 281.


2024-01-09-00
1: Modified the pause mechanism to resume from the current position when paused and restarted;
2: Enabled operations such as copy, paste, and delete for folders and filenames containing spaces.
3: Add macro window with input box for #2070, for example: #2070=100(Dialog Box Title: ); The address after the equal sign is the macro variable address, ranging from 50 to 499.


2024-02-02-00
1: #1505 can print macro addresses (#1510-#1513).

2024-03-10-01
1: Fixed the FUP[] macro operator instruction.
2: Solved the issue where CAM files couldn't load processing after removing the USB flash drive.
3: Fixed the issue of the "Clear Local" function in the file management interface sub-menu being ineffective.

2024-03-15-00
1: Add parameter #93, which allows selecting whether to start processing from the current line's starting point or from a new position when pausing and restarting.

2024-03-16-00
1: Increase the quantity of images in the CAM library to a total of 30;
2: Modify the issue where the first parameter does not refresh when switching CAMs.


2024-03-20-02
1: Fixed the issue of CAM interface freezing upon startup in the previous software version of V2.
2: CAM parameters can now be saved when disconnected.

2024-03-22-00
1: Added USB barcode scanner file selection function;(pr210=1396,pr278=2)

2024-03-23-00
1: CAM parameters (#2500-#2999) support assignment and can be saved as parameters.


2024-03-26-00
1: [V2] Added system power supply voltage detection. When voltage fluctuations beyond the normal range are detected, a prompt will be given.

2024-03-28-00
1: Processing files with filenames starting with "macro" will default to enabling macro parsing functionality.
2: All CAM files should be named macro_cam10.nc and need to be placed in the local disk (local) CAM folder. The folder can be copied entirely from a USB drive to the local disk.
3: When modifying the super administrator password, the original password must be entered for modification to take place.

2024-03-30-00
1: Increase character length for displaying CAM names.